Thorens Standard Drive Belt Replacement OEM with Logo

$29.33

 

Nothing works like a genuine Thorens standard belt with logo.  Once your new turntable is adjusted using this belt, all you will need to do in the future is just order this same belt again. If you keep switching belt manufacturers, you will never get things quite right twice in a row. Before checking out, explore other Thorens replacement and upgrade parts. 

16 in stock

Description

Genuine German-made Thorens standard drive belt, part number 6800574 which will fit:
Thorens TD105, 115, 125, 125MKII, 126,  126 mkii, 126 mkiii, 127, 145,  14, 6,  147,  160 Super
150,  150 II,  158,  160,  160B,  160 B MK II,  TD-160 MKII, 165,  166,  166 MKII,
170, 190, 2001, 226  226, 235,  240  280Mk I, 280 Mk 11, TD-126 MKII
280 Mk III,  290, 295, 3001, 316, 318, 320, 321, 325, 520,  521.
 
 
100% guaranteed to work on the models above or may be returned for full refund minus return shipping. 
 
Visit Vinyl Nirvana for more information on AR and Thorens turntables.   
From the Vinyl Nirvana blog, 4-21-2007
 

In praise of the lowly belt…

Though everyone familiar with AR and Thorens turntables acknowledges the importance of the spring suspended subchassis to isolation of unwanted resonances, another critical component of this isolation is often ignored: the belt. Inherent in the fact that the three-spring suspension allows the sub-chassis to FLOAT, is the fact that an improperly sized belt will cause the sub-chassis to be aligned incorrectly. (Most often, an overly tight belt will pull the entire suspension towards the motor.)

In addition to its importance to proper fucntioning of the suspension, the correct belt size will also ensure there is constant velocity between the motor pulley and the drive platter. Any kind of slippage will result in speed variations.

Finally, in the case of the Thorens, where speed change is accomplished mechanically, a high quality belt of the correct dimensions will ensure the proper change of speeds. You won’t find the belt riding midway between 33 and 45rpm.

To sum up, a high quality belt will allow independent motion of the subchassis, yet drive the inner platter at a constant speed by friction. It’s a complex balance that can only be achieved by a correctly sized belt of good quality rubber. (I wish you were here with me now so I could show you the difference in feel between a belt of good quality rubber and one that seems to be made of a poor synthetic rubber. The former has a suppleness and evenness of tension; the latter is slippery and lacks elasticity.)

It is almost comical to me how some folks will spend hundreds of dollars on the their cartridge, but then skimp on the quality of their belts. Come on, spending eighteen or twenty-five dollars on such an integral part of your vinyl playback system should not be so hard when you have already invested so much. Would you rather spend it on a new motor caused by an overly tight belt stressing your bearings?

Feedback

Music matters to me, the turntable I have was throwing the old belt off and the wow and flutter was detectable when it ran. maybe another belt would be as good, but it could not be better. Faultless fit and, straight away, performance like new. I firmly recommend this product.”

“If you have a Thorens deck, don’t buy a cheaper generic belt. You will have problems with the speed especially 45s. Get this, pay the extra and do it properly.”

” It costs more, but a proper belt is better than some piece of rubber belt, which other suppliers seemed to be offering. On receipt the new belt was more than 1 inch shorter than my old one, measured loop to loop, so hence the problem with speed switching I was having. A check to center the belt onto the bottom pulley and the turntable was like new again.”

“This is a must for any Thorens I never realized how bad these other belts are.”

Additional information

Weight2 oz
Dimensions9 × 6 × 1 in